DDC公司产品

一、 数据总线接口
MIL-STD-1553芯片：适用于DDC公司的各MIL-STD-1553卡及其他产品。

型 号
封 装
说 明
BU-61865EnhancedMini-ACE

BU-61845

BU-61843

BU-61864

 72 Pin Quard Flatpack(1.0×1.0")

The Enhanced Mini-ACE family of MIL-STD-1553 terminals provide complete interfaces between a host processor and a 1553 bus. These terminals integrate dual transceiver,protocollogic, and 4K or 64K words of RAM.

BU-61580ACE,

BU-61581,

BU-61585,

BU-61586

70 Pin DIP 1.9×1.0×0.165"

 The ACE Bus Controller/Remote Terminal/Monitor Terminal(BC/RT/MT) terminals comprise a complete integrated interfacebetween a host processor and a MIL-STD-1553 A and B or STANAG 3838 bus.

BUS-65153STIC,

BUS-65154

BUS-65163

BUS-65164

70-pin ceramic DDIP, and flat pack (1.9 x 1.0 x 0.2 inches)

 MIL-STD-1553B, NOTICE 2 AND MIL-STD-1760B SMALL TERMINAL INTERFACE CIRCUIT 'STIC'. Complete dual redundant MIL-STD-1553B Notice 2 and MIL-STD-1760B. This Small Terminal Integrated Circuit (STIC) Remote-Terminal(RT) allows a direct interface to simple systems. Includes CMOS Protocol and BiPolar low power MK II (BUS63100) transceivers, timing control logic, and latchable RT address.
BU-62743/62843/62864

72 Pin Quad Flat Pack (1.0 x 1.0)

 The PCI Enhanced Mini-ACE? MIL-STD-1553 series is the industry's first fully integrated solution for interfacing a 32-bit, 33-MHz PCI bus with a MIL-STD-1553 bus. A distinct improvement over multi-component implementations, the PCI Enhanced Mini-ACE reduces real estate and power requirements while eliminating the need for custom FPGA logic by providing a direct interface to embedded PCI buses. To accelerate host write operations, the interface incorporates a built-in FIFO that enables a PCI master to transfer a 32-word 1553 message in approximately 1.5 μs.
 

 

二、 ARINC429商用航电芯片
ARINC429芯片：使用离散/数学、开放/数字接口实现离散型号到数字信号的转变。

型 号
封 装
说 明
DD-00429

ARINC 429 MicroprocessorInterface

 144-PIN TQFP0.87×0.87×0.063" The DD-00429 provides a complete and flexible interface between a microprocessor and an ARINC 429 data bus. The DD-00429, when configured with two DD-03282 Transceivers, supports four ARINC Receive channels (Rx0, Rx1, Rx2 and Rx3) each receiving data independently.
DD-42900

ARINC 429 MicroprocessorInterface Device

 64-Pin DIP or Flat Pack2.00 x 2.00 x .137 in.50.8 x 50.8 x 3.48 mm. The DD-42900 provides a complete and flexible interface between a microprocessor and an ARINC 429 data bus. It contains four Rx's, two Tx's, and RAM/FIFO's.

 

三、MIL-STD-1553仿真测试、接口板卡

型 号
封 装
说 明

BU-65570I

BU-65572I

MIL-STD-1553 PCIDual Tester/Simulator Card

 DDC's BU-65570I/72I is a versatile, PCI Card designed for the test and simulation of MIL-STD-1553 systems. It provides full, intelligent interfacing for one or two serial dual redundant MIL-STD-1553 data buses and a PCI chassis. The BU-65570I/72I offers 64K Words of Shared RAM per Channel and Simultaneous Emulation of BC, 31 RTs, and MT for Each Channel.
BU-65570M

MIL-STD-1553 PCMCIA CARD

 DDC's BU-65570I/72I is a versatile, PCI Card designed for the test and simulation of MIL-STD-1553 systems. It provides full, intelligent interfacing for one or two serial dual redundant MIL-STD-1553 data buses and a PCI chassis. The BU-65570I/72I offers 64K Words of Shared RAM per Channel and Simultaneous Emulation of BC, 31 RTs, and MT for Each Channel.
BU-65565

MIL-STD-1553 Four-Channel PMC Interface Card

 The BU-65565 is a MIL-STD-1553 PMC card available with one to four dual redundant, Enhanced Mini-ACE 1553 channels. Each channel can be independently programmed for BC, RT, Monitor, or RT/Monitor mode.
BU-65549

MIL-STD-1553 BC/RT/MT PCI Interface Card

 The BU-65549 is a 32-Bit, 33 MHz PCI target interface card which provides an intelligent interface between a PCI bus and a MIL-STD-1553 bus. The BU-65549 allows for operation as one or two dual redundant Bus Controllers, Remote Terminals, Monitor Terminals, or combined Remote Terminal / Monitor Terminals. The card offers flexible RT data buffering and interrupt generation.

BU-65527

BU-65528

MIL-STD-1553B BC/RT/MT VME/VXI Interface Card

 The BU-65527 and BU-65528 provide an intelligent interface between a VME/VXI bus and up to four independent MIL-STD- 1553 buses. Each 1553 channel may be programmed for operation as a Bus Controller, Remote Terminal, Monitor Terminal, or combined Remote Terminal / Monitor Terminal. The BU-65528 is available as either an air-cooled commercial grade, or a conduction cooled military grade card.
BU-65553

MIL-STD-1553 PCMCIA InterfaceCard

 DDC's BU-65553 is a Type II, 2.10 Compatible PCMCIA Card designed for the test and simulation of MIL-STD-1553 systems.Based on DDC's new Enhanced Mini-ACE, it provides full, intelligent interfacing between a dual redundant MIL-STD-1553 data bus and a PCMCIA slot. The BU-65553 provides flexible RT data buffering, with global circular buffer and half-full and full interrupt capability.
BU-65569i

MIL-STD-1553 PCI Card

 The BU-65569iX is a single-channel or multi-channel MIL-STD-1553 PCI card. The BU-65569iX includes one to four dual redundant 1553 channels. The design of the BU-65569iX leverages the Enhanced Mini-ACE. Each channel may be independently programmed for BC/RT/Monitor, or RT/Monitor mode.
BUS-65518

IBM� AT Compatible MIL-STD-1553 Simulator and Tester Card

 The BUS-65518 (Half-size) and BUS-65517II (Full-size) cards are
16-Bit ISA Bus devices that provide full MIL-STD-1553 test and
simulation capabilities. These capabilities include operation
as a Bus Controller, multiple Remote Terminals, and a simultaneous
Bus Monitor. In addition, the BUS-65518 provides comprehensive
1553 error injection and detection capabilities.

 

四、ARINC429商用航电板卡

型 号
封 装
说 明

DD-42916/32V3-300

 ARINC 429 VME Interface Card The DD-42916/32V3-300 contains up to two DD-42916C1-300 PMC modules installed on a VME carrier card. The card contains 32 programmable Rx/Tx channels, with high-speed/lowspeed operation, and engineering unit conversion, and can be used for analyzing and simulating data on an ARINC 429 Data Bus.

DD-45322P1-300

 ARINC 453/708 WeatherRadar Interface Card The DD-45322P1 card is a full-length ISA PC card that contains2 Tx and 2 Rx ARINC 453/708 channels to communicate withweather radar displays and 2 Tx and 2 Rx ARINC 429 channels.

DD-42916I3-300

 ARINC 429 PCI Interface Card The DD-42916I3-300 contains one DD-42916C1-300 PMC module installed on a PCI carrier card. This card is designed specifically to interface with an ARINC 429 data bus. With16programmableRx/Tx channels, high-speed/ low-speed operation on all channels simultaneously, and engineering unit conversion this card is well suited for all types of data acquisition.

DD-42924I5-300

ARINC 429 PCI InterfaceCard The DD-42924I5-300 is a PCI card designed specifically to interface with an ARINC 429 / 575 data bus. This card contains2 transmit channels and 4 receive channels, along with five discrete inputs and outputs. The DD-42924I5-300 can be used as a data source for simulating data on an ARINC 429 Data Bus or as a data receiver for analyzing data from an ARINC 429 Data Bus.

DD-42916C1-300

 ARINC 429 PMC (PCIMezzanine Card) The DD-42916C1-300 is a PMC (PCI Mezzanine card) designedspecifically to interface with an ARINC 429 data bus. The card contains 16programmable high-speed/low-speed Rx/Tx channels, supports high-speed data rates on all channels simultaneously,and can be used as a data source for analyzing and simulating data from an ARINC 429 Data Bus.

DD-42921M2-300

 ARINC 429 PCMCIA 2Rx/1Tx ARINC-429-PCMCIA Interface Card,Type II, PCMCIA 2.10 compatible. Two Arinc 429 Receive channels and one transmit channel, all integrated on the card. No external transmission module is necessary. Label and SDI filtering and mailbox reception done on the card. 32 word FIFO's for each channel. Built-in fault detection. Free library software

DD-42912/24M3-300

 ARINC 429 PCMCIA Card The DD-42912M3-300 and DD-42924M3-300 are two versions of a high density, Type II PCMCIA card for interfacing with an ARINC 429 data bus. The DD-42912M3-300 version features one transmit channel, two receive channels, and two discrete outputs; while the DD-42924M3-300 contains two transmit channels, four receive channels, and one discrete output. The card can be used as a data source for simulating or data receiver for analyzing data on a bus. With excellent transfer reliability, the card provides scheduled and FIFO transmissions, receive data filtering and time stamping, and FIFO and mailbox reception modes.

DD-42988V0-300

 ARINC 429 VME/VXI ARINC-429-VME/VXI card that contains 8 programmable high or low/speed, Tx or Rx, and 8 low/speed receive only channels. Five on-board processors provide high performance usage and on-board engineering unit conversion.

 

五、远程电源控制器

型 号
封 装
说 明

SSP-21116

 (16-Pin DIP)2.0 x 3.0 x 0.33 in.50.80 x 76.20 x 8.38 mm. The SSP-21116 Series of 270 Volt, dc, Solid-State Power Controllers (SSPCs) replace electromagnetic circuit breakers and solid-state relays rated at 10 and 15 amperes. These SSPCs offer status outputsand permit external input logic control so that they may be remotely located near to the load. There are four models in the series, differing only in rated current, so that fault and I2T trip characteristics can be selected to protect wiring and loads.

RP-21000

 2.74 x 1.34 x 0.32 in.69.60 x 34.04 x 8.26 mm. The RP-21000 Series (formerly SSP-21110 Series) of 28 Vdc, Solid-State Power Controllers (SSPC's) replace electromagnetic circuit breakers and solid-state relays rated from 2 through 25 amperes.

SSP-21120

 3.13 x 3.75 x 3.00 in.79.50 x 95.25 x 76.20 mm. The SSP-21120 Series of 28 Vdc, Solid-State Power Controllers (SSPCs) replace electromagnetic circuit breakers and solidstate relays rated for 40, 60, and 80 amperes. The SSPCs offer status outputs and permit external input logic control allowing for remote location near to the load. The three models in the series differ only in rated current, so that fault and I2T trip characteristics can be selected to protect wiring and loads.

RP-21203

RP-21209

RP-21225

 RP-21203 [1 to3 A ](1.5 x 1.2 x 0.44 inches)RP-21209 [3 to 9 A] (1.5 x 1.5 x 0.44 inches)Rp-21225 [ 8.3 to 25 A] (1.5 x 2.2 x 0.44 inches) STAR series, Solid-STate Advanced Remote Power Controllers,28Vdc, programmable 1 to 25 amperes. Optional analog current output monitor. The STAR series offers reliable I2T trip protection, programmable current, instant trip, and load detection status settings, while providing isolated control circuitry .

 

六、移动反馈技术产品：自整角机及旋转变压器产品

1、S/D、R/D模块

型 号
分 辨 率
精 度
速 度
说 明

RD-19230

 10, 12, 14, or 16 Bits
+2.3
 1152 rps The RD-19230 is a small 16-bit monolithic Resolver-to-Digital,single chip converter that offers programmable features such as resolution, bandwidth, velocity output scaling and encoder emulation.

RDC-19220/2S

 10, 12, 14, or 16 Bits
+2.3
 to2300rps The RDC-19220/2S is a 16-bit monolithic Resolver-to-Digital, single chip converter that offers programmable features such as resolution, bandwidth, and velocity output scaling. The internal Synthesized reference section eliminates errors due to quadrature voltage.

RDC-19220/2

 10, 12, 14, or 16 Bits
+2.3
 2300rps The RDC-19220 series of converters are 16-bit monolithic Resolver (/LVDT)-to-Digital, single chip converters that offer programmable features such as resolution, bandwidth, and velocity output scaling.

SD-14590/91/92

 14, 16, 14/16 Bits
+1.3
 10 rps

The SD-14590/91/92 series of converters replaces manylegacy units. User-programmable resolution has been designed into the SD-14590 to increase the capabilities of modern motion control systems. The precise positioning attained at 16 bits of resolution and fast tracking of a 14-bit device are nowavailable from one 36-pin double DIP hybrid.

SD-14550 SERIES

 10, 12, 14, or 16 Bits
+1.3
 0.5 to 160 rps The SD-14550 Series are small complete Synchro- or Resolverto-Digital converters based on a single-chip monolithic. The SD-14550X"S" option offers synthesized reference circuitry to correct for phase shifts between the reference and signal voltage.

SD-14595/96/97

 14 or 16 Bits
+1.3
 10 rps The SD-14595/96/97 series converters replace many discontinued Natel units. Other features are solid-state signal andreference isolation with high common-mode rejection.Packaged in a 36-pin DDIP, the SD-14595/96/97 series featureBuilt-In-Test (BIT) output.

SD-14620 SERIES

 10, 12, 14, or 16 Bits
+1.3
 0.5 to 160 rps The SD-14620 Series converters are small, low-cost, two-channelhybrid Synchro- or Resolver-to-Digital converters based on a single-chip monolithic. The SD-14620X "S" option offers synthesized reference circuitry to correct for phase shiftsbetween the reference and signal inputs. The two channelsare independent but share the digital output and +5 VDCpower pins.

SDC-630/632/634 A/ST

 10, 12, or 14 Bits
+2.1
 50 rps The SDC-630/632/634 A/ST series are low cost, low profileSynchro-to-Digital (S/D) and Resolver-to-Digital (R/D) trackingconverters with standard pin configurations. They use aunique control transformer algorithm that provides inherentlyhigher accuracy and jitter-free output.

SD-14610/15 SERIES

 14 16 Bits
+1.3
to 10 rps The SDC-14610/15 Series are small low cost three channelSynchro- or Resolver-to-Digital converters. The three channelsare independent tracking types but share digital output pins and a common reference. Synthesized reference option now available.

 

2、D/S、D/R模块

型 号
分 辨 率
精 度
速 度
说 明

DR-11525

 16 Bits
to ±1
 2 mA-rms The DR-11525 can be used as: a digital-to-resolver converterusing a sinusoidal reference as an input; a digital-to-sin/cosdc converter using a dc reference; a polar-to-rectangularconverter using a reference input proportional to the radiusvector; or a rotating cartwheel sweep generator for PPI displaysusing a sawtooth reference.

DSC-11524

 16 Bits
to ±2
 15 mA The DSC-11524 is a complete D/S and D/R converter in one hybrid module.The reference input will accept any waveform,even a sawtooth for a CRT drive.

DSC-10510

 16 Bits
to ±2
 7 VA The DSC-10510 is a high power digital-to-synchro convertercapable of driving multiple Control Transformer (CT), ControlDifferential Transmitter (CDX) and Torque Receiver (TR) loadsup to 7 VA.

DRC-10520

 16 Bits
to ±1
 2 VA The DRC-10520 is a high power, 16 bit Digital-to-Resolver converter with 2 VA drive capability. It features a power amplifier that may be driven by a standard ±15 VDC power supply or by the reference source (when used with the optional powertransformer DDC/PN 29306).

 

3、S/R指示、模拟器

型 号
功 能
分辨率
精 度
说 明
SIM-36010

Synchro/Resolver AngleSimulator ISA Card 16 Bits 25Arc.Sec(±0.007°） The SIM-36010 providesSynchro or Resolver output signals ofeither 11.8, 26, or 90 Volts L-L with a drive capability of 1.5 VA. The SIM-36010 also includes a programmable dynamic rotationfeature which provides for a programmable constant rate, either CW or CCW from 0.17°/sec up to 30.5 rps.

API-36005

 Synchro/Resolver AngleIndicator ISA Card 20/16 Bits 18 Arc.Sec.(±0.005°) The API-36005 is a full-size 8-bit ISA card containing a broadbandSynchro/Resolver Angle Position Indicator.

 

4、转换卡

型 号
分辨率
精 度
封 装
说 明

SB-36220IX

 12 or 16 Bits 1 to 4 Min. 6-Channel D/S-D/R ConverterPCI Interface Card The SB-36220IX card is a PCI bus card that contains up to six channels of fully independent Digital-to-Synchro (D/S) orDigital-to-Resolver (D/R) converter(s). An optional on-board reference that can be configured for 2, 26 or 115 volts eliminates the need for an external oscillator.

SB-36320CX

 16 Bits 4, 2 or 1 Min. 2-Channel D/S - D/RConverter PC-104 Card The SB-36320CX is a PC-104 card which contains up to two channels of Digital-to-Synchro (D/S) or Digital-to-Resolver(D/R) conversion. This card is ideal for simulating Synchro or Resolver format signals.

SDC-36016

 10, 12, 14 or 16 Bits 2 to 9 + 1 LSB Min. Four Channel S/D-R/DConverter ISA Card The SDC-36016 is a full-size 8-bit ISA card containing one tofour independent channels of Synchro-to-Digital (S/D) or Resolver-to-Digital (R/D) conversion. The SDC-36016 also features a Built-In-Test with loss of signal and loss of reference detection.

DSC-36020

 16 Bits 1 to 4 Min. Six-Channel D/R-D/SConverter ISA Card The DSC-36020 is a full-size 8-bit ISA card which generates up to six channels of sine/cosine, synchro, or resolver signals. The converter card uses the DSC-11520 (low power) or DSC-11524 (higher drive).

SB-36210IX

 10,12,14 or 16 Bits 1 to 3 + 1 LSB Min. 6-Channel S/D, R/D orLVDT/RVDT -To-Digital PCI Interface Card The SB-36210IX is a PCI bus card that contains six channels of fully independent Synchro-to-Digital (S/D), Resolver-to-Digital(R/D) or LVDT/RVDT-to-Digital conversion. The SB-36210IX card has self-test and optional power oscillator to support 2 Vrms, 26 Vrms or 115 Vrms from 57 to 7kHz.

SB-36310CX

 10,12,14 or 16 Bits 1 to 2 + 1 LSB Min. 4-Channel S/D - R/DConverter PC-104 Card The SB-36310CX is a PC-104 card which contains one to fourchannels of fully independent Synchro-to-Digital (S/D) orResolver-to-Digital (R/D) conversion. Each channel can be configured for a 90 V or 11.8 V line-to-line Synchro/Resolver(S/R) or 2 V sin/cos signal input, with 10-, 12-, 14-, or 16-bitresolution.

DSC-36022

 14 Bits 4 Min. Four-Channel D/R-D/SConverter ISA Card The DSC-36022 is a full-size 8-bit ISA card which generates up to four channels of Synchro or Resolver output signals. Forapplications requiring up to 1.5 VA of drive capability theDSC-644 Series of converter modules can be used. For higher drive, 90 VL-L 400 Hz Synchro applications, the DSC-544 can be used.

SB-36110VX

 10,12,14 or 16 Bits 4, 2 or 1 + 1 LSB Min. 12-Channel VME S/D - R/DConverter Card The SB-36110VX is a twelve-channel, 6U, B size, VME card which can be configured in 3, 6, 9, or 12 channels of fully independent Synchro-to-Digital (S/D) or Resolver-to-Digital (R/D)conversion. Separate reference inputs are provided for each group of three converters (four reference groups for the 12 channels).

 

5、特殊功能产品

OSC-15801 - Synchro/Resolver/Inductosyn Reference Oscillator：The OSC-15801 is a quadrature power oscillator with two outputs that are 90° out of phase. These outputs provide both the
reference and quadrature signals, simultaneously, making the OSC-15801 ideally suited for Inductosyn applications.

SD-15900 - Two-Speed S/D or R/D Combiner Converter：The two-speed combiner is designed to work in conjunction with any two Synchro-to-Digital (S/D) or Resolver-to-Digital (R/D) converters such as DDC's two-channel SD-14620 Series or two RDC-19220 Series. These combinations provide a complete solution to implement two-speed S/D or R/D conversion.

SBA SERIES SYNCHRO BOOSTER AMPLIFIER: 25VA drive(6 W active load).Kick circuit prevents 180°hang-up. Internally powered from reference. Short circuit, transient, and overload protected.

 

七、有刷/无刷（感应）电机驱动器/控制器

型 号
电 压
电 流
封 装
说 明

PW-82520R

 100 V 1 / 3 / 10 A 2.60 x 1.40 x .250 in. The PW-82520R (100Vdc) is a radiation tolerant, current regulating torque loop controller designed to accurately regulate the current in the motor windings of 3-phase brush and brushless DC motors.

PW-83075, PW-84075, PW-85075

 270 V 200 mA250 mA 2.89 x 1.48 x 0.69 in. The PW-83075, PW-84075, and PW-85075 are half-bridge drivemodules containing isolated switch drivers, a pair of solid stateswitches, and an isolated power supply.

PWR-82332

 400 V 19 A 3.00 x 2.30 x .400 in. The PWR-82332 is a 3-phase, 19A motor drive hybrid whichincorporates a 400 Vdc MOSFET output stage for high-speed,high current, and high-efficiency operation.

 

下一页